Add-Ons & Components

• Stabilizes shaky camera images
• Works with Standard Analog Cameras
• Works with Standard Analog Cameras
• NTSC or PAL Video In and Out
• Composite Video In & Out (S-Video Optional)
• Unlimited Spatial Correction

Digitally stabilize shaky and unsteady analog video images live or pre-recorded. Color, Monochrome, or Thermal cameras supported. Cameras mounted on poles, towers, UAVs, or vehicles that shake and vibrate can easily be steadied using the RHP-IS-OEM Digital Image Stabilizer.

• Works with Standard Analog Cameras
• NTSC or PAL Video In and Out
• Composite Video In & Out (S-Video Optional)
• Unlimited Spatial Correction
• Full Resolution
• Particularly Suitable for:
  • Buses
  • Trains
  • Ships and Boats
  • Airplanes and Helicopters
  • Tall Buildings
  • Bridges and Tunnels
  • Coastal Surveillance at windy locations
  • Factories with Vibration from Machinery or air conditioning
  • Pole-Mounted Cameras e.g. Traffic monitoring.

Stabilized video from the RHP-IS-OEM video shows cleaner details. Sharp details are a requirement for good and high quality video. Steady video compresses better. Modern digital compressors use a lot of bits to encode moving features of a video. If the whole image shakes, it is all moving. This wastes an enormous number of bits.

Remove the shake and digital recorders store more video. For the same reason, stable images have higher compression and quality for remote and Internet viewing.

USB2.0 Cable - USB2-A-B-6 - 6Ft Type A to Mini B

FLIR Tau PCB Wearsaver with Solder Pads

A low-profile adapter that attaches to the Tau's 50-pin Hirose connector, furnishing a solder pad interface. Schematic included.

The Tau2 Wearsaver was designed to be an internal engineering/manufacturing calibration accessory, rather than an OEM interface.
There is a Hirose mating connector on one side of the board, as shown in the picture below:

When the Wearsaver is attached to the Tau2 camera, there are no exposed connectors, just the solder pads for a 20-pin Samtec (and 14 pads for pogo pins).

The pad connections are limited to input power, RS-232, analog video, and LVDS.

The Wearsaver board does NOT provision for External Sync, Discretes, or CMOS signals.

The physical layout is shown in the picture below:

Cable kit consisting of three power cables (UK,EU,US).

Side Mount Payload Bracket (1)
Side-mounting payload bracket for the PTU-5 pan tilt. Up to 3 lb capacity per side, 6 lb total with two side brackets. Side bracket use requires removal of the PTU-5 top bracket. (Side and top brackets cannot be used together at the same time.)

• USB 3.0 cable
• End 1: USB 3.0 (Type-A)
• End 2: USB 3.0 (Micro-B) Locking screws
• 3 m in length

Pole Junction Box

Pole Junction Box for FB-Series Thermal Security Cameras.

Allows the FLIR FB Series O and FB Series ID cameras to be mounted on a Pole

Wall Junction Box

Wall Junction Box for FB-Series

Allows the FLIR FB Series O and FB Series ID cameras to be mounted on a Wall

24VAC Outdoor Power Supply

The FLIR 24VAC Outdoor Power Supply provides power via two (2) fuse-protected outputs for FLIR thermal security cameras. The power supply offers a variety of configurations to power up to four outdoor units from a single source. With two 24 or 28 VAC outputs, the 24VAC Power Supply compensates for voltage losses over long wire runs and offers different input voltages. Capable of powering integrated systems, the power supply also allows for full use of cameras with pan/tilt, heating, and blowing functionalities.

North American power supply for FLIR pan/tilt units.

Power supply, 30V, w AC Cord

European power supply for all FLIR pan/tilt units.

Power supply, 30V, w EURO Cord

Breakout Cables

The breakout cable connects to the 32 pin base connector (MIL C 26482) on the PTU and terminates to standard connectors for power, serial communication, Ethernet, and payload signals.

The terminating connectors are:

• Power (DIN), 2x video (composite),
• RS 232 (DB 9, female),
• RS485 (RJ11),
• Ethernet (RJ45),
• Payload pass through conductors.

Part Number:

PTU CAB E 10BO (10')
PTU CAB E 25BO (25') 
PTU CAB E 50BO (50')
PTU CAB E 100BO (100')

PT-Series Small Pole Adapter

High capacity pole mount for pole diameters between 80mm-150mm

Teledyne FLIR Neutrino LC Development Kit

Provides all output options on a single PCB and easy access to the full 80-pin camera interface for development.
Includes a flex cable between the board and the camera and a wire harness to the cooler interface.