Products

Cable to access signals in M12 connector,‎ pigtail.

Environmental Enclosure

for the Teledyne FLIR Boson

In today's technological world, it is crucial to protect your Teledyne FLIR Boson Thermal Imaging Camera from environmental factors that can lead to costly damages and loss of productivity. The RHP Boson Environmental Enclosure is a cutting-edge solution that ensures the safety and longevity of your valuable devices. With its IP67 rating and exceptional features, this enclosure is the ultimate choice for safeguarding your camera.

IP67 Rated Protection

One of the standout features of the RHP Boson Environmental Enclosure is its IP67 rating. This international standard certifies the enclosure's ability to provide complete protection against the intrusion of dust and water.

IP67 rating stands for:

• IP (Ingress Protection)
• 6 (dust-tight protection)
• 7 (protection to withstand temporary submersion in water up to depths of 150mm to 1000mm deep for 30 minutes).

Whether the Boson is operating in a dusty industrial environment or exposed to heavy rainfall in an outdoor setting, the Boson Environmental Enclosure guarantees uncompromised protection against these elements.

This cable is used to connect the infrared camera to Ethernet.

FC Series Wall mount

4129742

The FC-Series cameras are an infrared thermal imaging camera intended for outdoor security applications, and can be installed in a fixed location or on a pan/tilt mechanism. The FC-Series cameras are intended to be mounted on a medium-duty fixed wall mount commonly used in the security industry.

This camera mount supports up to 5.4 lbs (2.5 kg). Cables may exit from the back of the camera housing through the supplied cable gland or from the bottom of the camera housing when using the concealed cable wall mount

A cable gland plug is supplied for the rear of the camera housing when cables are routed using the concealed cable wall mount.

Simplify camera setup with the Teledyne FLIR FH Series Wall Mount Kit, offering a reliable and efficient solution for mounting the FH Series Thermal Cameras.

This wall mount kit is thoughtfully engineered to provide a secure and flexible installation option, allowing you to position your cameras at the desired height and angle.

Its robust construction ensures long-lasting performance, guaranteeing a stable and unobtrusive solution for all your mounting requirements.

FLIR MCS pan-tilts are designed for high-performance control with low-latency and jitter and high command rates. There are multiple ways to control the units. FLIR MCS pan-tilts support both a simple ASCII command protocol, documented in the E Series Command Reference Manual as well as a binary form of the commands, supported by a portable C language library (PTU-SDK). The PTU-SDK is provided as source code and can be compiled on any computing platform. It allows applications to send commands to the pan-tilt over serial or Ethernet interfaces seamlessly.

Transport Case

Rugged, watertight plastic shipping case for FLIR A3XX, A6xx series. Holds all items neatly and securely. The case can be locked with padlocks and features a membrane to prevent pressure build-up in airplane cargo holds.

ioi PTZ Tracker

Distributed Intelligent Video Encoder

The PTZ Tracker analyzes video signals and sends alarm notifications when people, vehicles or objects cross perimeter lines, enter pre-defined regions, or are left behind or removed from scenes. Users can customize zones and define what to detect. With Pan/Tilt/Zoom (PTZ) cameras, once a moving object is detected, the PTZ tracker automatically controls the PTZ camera to autonomously track and zoom in on potential threats.

RHP-BOS-VPC-IF

Video Power Communication Interface

The RHP Boson VPC Interface is a remarkable low profile electronic module geared towards offering simple integration with the FLIR Boson. Its cutting-edge design includes reverse polarity protection, which secures your device from any irreversible damage due to voltage. It features 5 to 26v input, a vital function that enables this interface module to deliver consistent power for extended use.

Its USB video support allows you to stream video via USB, and the Sync in/out ensures synchronization with other devices. Experience seamless performance with this efficient and dependable interface module.

* Please Note: External Sync is disabled on Boson ≤9Hz Cameras.
The use of external sync on these cameras is not supported because pulses cannot be correlated to a specific output frame because of the way the reduced frame rate video is created. If attempted, the camera will reject commands to begin external sync mode.

This kit includes:

• 6-PIN JST to USB/RCA Video cable (x1)
• 6-PIN JST to Bare End Leads (x2)
• M1.6 Screws (x4)
• Allen Key (x1)
• RHP BOS VPC-IF Board (x1)
• Quick Start Guide (x1)

RHP-BOS-VPC3-IF - USB3

Video Power Communication Interface

Introducing the Low Profile VPC Interface Module, specifically designed for the FLIR Boson. With improved heat dissipation, this module ensures optimal performance in even the most demanding environments. With Video Power & Communication support and reverse polarity voltage protection, this module is compatible with power ranging from 5 to 26 volts DC. Power can be supplied via USB3, and video support is also available through USB3. Stream video to a PC via USB3 and enjoy seamless Sync-In/Out capabilities with this state-of-the-art interface module.

* Please Note: External Sync is disabled on Boson ≤9Hz Cameras.
The use of external sync on these cameras is not supported because pulses cannot be correlated to a specific output frame because of the way the reduced frame rate video is created. If attempted, the camera will reject commands to begin external sync mode.

This kit includes:

• 6pin JST (USB2.0 + Sync)
• 7pin JST (USB3)
• M1.6 Screws (x4)
• Allen Key (x1)
• RHP BOS VPC3-IF Board (x1)
• Quick Start Guide (x1)

RHP-LEP-VPC-IF

USB Video Power Communication Interface

Teledyne FLIR Neutrino LC Development Kit

Provides all output options on a single PCB and easy access to the full 80-pin camera interface for development.
Includes a flex cable between the board and the camera and a wire harness to the cooler interface.

• Stabilizes shaky camera images
• Works with Standard Analog Cameras
• Works with Standard Analog Cameras
• NTSC or PAL Video In and Out
• Composite Video In & Out (S-Video Optional)
• Unlimited Spatial Correction

Digitally stabilize shaky and unsteady analog video images live or pre-recorded. Color, Monochrome, or Thermal cameras supported. Cameras mounted on poles, towers, UAVs, or vehicles that shake and vibrate can easily be steadied using the RHP-IS-OEM Digital Image Stabilizer.

• Works with Standard Analog Cameras
• NTSC or PAL Video In and Out
• Composite Video In & Out (S-Video Optional)
• Unlimited Spatial Correction
• Full Resolution
• Particularly Suitable for:
  • Buses
  • Trains
  • Ships and Boats
  • Airplanes and Helicopters
  • Tall Buildings
  • Bridges and Tunnels
  • Coastal Surveillance at windy locations
  • Factories with Vibration from Machinery or air conditioning
  • Pole-Mounted Cameras e.g. Traffic monitoring.

Stabilized video from the RHP-IS-OEM video shows cleaner details. Sharp details are a requirement for good and high quality video. Steady video compresses better. Modern digital compressors use a lot of bits to encode moving features of a video. If the whole image shakes, it is all moving. This wastes an enormous number of bits.

Remove the shake and digital recorders store more video. For the same reason, stable images have higher compression and quality for remote and Internet viewing.

European power supply for all FLIR pan/tilt units.

Power supply, 30V, w EURO Cord